Difference between revisions of "EShapeoko 1.2 Assembly: Prep work"
(→Deburr) |
|||
| (12 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== Deburr == | == Deburr == | ||
| − | |||
| − | |||
Check the metal plates for burrs, droplets of metal, or spalsh marks. Scrape them off if possible, or file them off if necessary. | Check the metal plates for burrs, droplets of metal, or spalsh marks. Scrape them off if possible, or file them off if necessary. | ||
| Line 17: | Line 15: | ||
== Drill == | == Drill == | ||
| + | [[File:EShapeoko 1.2 assembly dual X rail prep.png|frame|right|Holes for bolting the two X MakerSlide pieces together (500 mm length shown)]] | ||
=== Dual X MakerSlide === | === Dual X MakerSlide === | ||
| Line 29: | Line 28: | ||
* 1000 mm: drill six holes every 143 mm. | * 1000 mm: drill six holes every 143 mm. | ||
| − | === Deluxe | + | === Deluxe Frame === |
| − | If you have the deluxe frame, you need to drill access holes for the Torx T25 key to reach the blind joint screws. | + | If you have the deluxe frame, you need to drill access holes for the Torx T25 key to reach the blind joint screws that hold the bottom of the frame together. |
| − | Identify the transversal pieces of 20 mm x 40 mm T-slot profile (parallel to the X axis). They are 60 mm or 65 mm longer than the X axis MakerSlide. Drill 5 to 5.8 mm diameter holes from the bottom of the T-slot on the 20 mm side all the way through both cores. If you don't have a drill press, it may be helpful to drill a pilot hole with a smaller drill first. It is important that these holes are positioned accurately and drilled squarely. It helps to make the holes as large as possible while still fitting within the 6 mm slot, because this gives more wiggle room for the Torx key if the holes | + | [[File:EShapeoko 1.2 assembly deluxe frame prep.png|frame|left|Access holes for the blind joints]]Identify the transversal pieces of 20 mm x 40 mm T-slot profile (parallel to the X axis). They are 60 mm or 65 mm longer than the X axis MakerSlide (the longitudinal pieces are exactly 80 mm shorter than the Y axis MakerSlide). Drill 5 to 5.8 mm diameter holes from the bottom of the T-slot on the 20 mm side all the way through both cores. If you don't have a drill press, it may be helpful to use a centre punch and drill a pilot hole with a smaller drill first. It is important that these holes are positioned accurately and drilled squarely. If you drill with a hand-held drill, clamp the profile or hold it in a vice — do not attempt to hold it with one hand and drill with the other hand. It helps to make the holes as large as possible while still fitting within the 6 mm slot, because this gives more wiggle room for the Torx key if the holes and the screws don't line up perfectly. |
Drill four holes in each of the transversal members of the frame, two near each end. Depending on the difference between the length of the extrusion and that of the X axis MakerSlide, drill them this far from each end: | Drill four holes in each of the transversal members of the frame, two near each end. Depending on the difference between the length of the extrusion and that of the X axis MakerSlide, drill them this far from each end: | ||
| Line 39: | Line 38: | ||
* extrusion 65 mm longer than the X MakerSlide: 29.0 mm and 49.0 mm. | * extrusion 65 mm longer than the X MakerSlide: 29.0 mm and 49.0 mm. | ||
For example, kits with 375 mm X come with 440 mm extrusion, so drill 29 mm and 49 mm from each end; kits with 750 mm X come with 810 mm extrusion, so drill 26.5 mm and 46.5 mm from each end. | For example, kits with 375 mm X come with 440 mm extrusion, so drill 29 mm and 49 mm from each end; kits with 750 mm X come with 810 mm extrusion, so drill 26.5 mm and 46.5 mm from each end. | ||
| + | |||
| + | == Go To == | ||
| + | * Next step: [[EShapeoko 1.2 Assembly: V-wheels|V-wheels]] | ||
| + | * Back to [[EShapeoko 1.2 Assembly Instructions|assembly top page]] | ||
Latest revision as of 18:05, 20 March 2015
Deburr
Check the metal plates for burrs, droplets of metal, or spalsh marks. Scrape them off if possible, or file them off if necessary.
Tap
Tap all the end holes in the MakerSlide M5×0.8mm (standard M5 thread), except the Z rail, which needs only one end tapped. Brush chips away and wipe the rail clean, to prevent damage to the V-wheels.
Tap the small holes in the belt tensioners, also M5×0.8mm.
Mark
Mark the side nearest the hole in the eccentric spacers by colouring it with a Sharpie or with a tiny dab of paint. The wheel will be offset in the marked direction.
Drill
Dual X MakerSlide
If you have a dual X rail kit with an X rail longer than 375 mm, please drill the X MakerSlide for the screws that hold the two rails together.
Lay the MakerSlide flat, Vs up, and drill 3 mm (or slightly larger) holes into the bottom of the T-slot, through the core. The slot has a fine groove on the bottom to help center the drill bit. The positioning of the holes along the MakerSlide is not critical. Drill both X pieces of MakerSlide the same way.
Depending on the length of the X MakerSlide, drill as follows:
- 375 mm: no drilling required;
- 500 mm: drill three holes every 125 mm;
- 750 mm: drill four holes every 150 mm;
- 1000 mm: drill six holes every 143 mm.
Deluxe Frame
If you have the deluxe frame, you need to drill access holes for the Torx T25 key to reach the blind joint screws that hold the bottom of the frame together.
Identify the transversal pieces of 20 mm x 40 mm T-slot profile (parallel to the X axis). They are 60 mm or 65 mm longer than the X axis MakerSlide (the longitudinal pieces are exactly 80 mm shorter than the Y axis MakerSlide). Drill 5 to 5.8 mm diameter holes from the bottom of the T-slot on the 20 mm side all the way through both cores. If you don't have a drill press, it may be helpful to use a centre punch and drill a pilot hole with a smaller drill first. It is important that these holes are positioned accurately and drilled squarely. If you drill with a hand-held drill, clamp the profile or hold it in a vice — do not attempt to hold it with one hand and drill with the other hand. It helps to make the holes as large as possible while still fitting within the 6 mm slot, because this gives more wiggle room for the Torx key if the holes and the screws don't line up perfectly.
Drill four holes in each of the transversal members of the frame, two near each end. Depending on the difference between the length of the extrusion and that of the X axis MakerSlide, drill them this far from each end:
- extrusion 60 mm longer than the X MakerSlide: 26.5 mm and 46.5 mm;
- extrusion 65 mm longer than the X MakerSlide: 29.0 mm and 49.0 mm.
For example, kits with 375 mm X come with 440 mm extrusion, so drill 29 mm and 49 mm from each end; kits with 750 mm X come with 810 mm extrusion, so drill 26.5 mm and 46.5 mm from each end.
Go To
- Next step: V-wheels
- Back to assembly top page