Difference between revisions of "EShapeoko 1.3 Assembly: Y belts"
Line 5: | Line 5: | ||
Refer to [[EShapeoko 1.3 Assembly: X and Y motors|the X and Y carriage instructions]] | Refer to [[EShapeoko 1.3 Assembly: X and Y motors|the X and Y carriage instructions]] | ||
− | for placement of the belt. | + | for placement of the belt. |
− | and two nuts | + | |
+ | Make four clamps out of two oval plates, two 10 mm long M5 screws, | ||
+ | and two nuts each. | ||
+ | |||
+ | Place one clamp a few millimeters from one end of the belt, and tighten firmly. Thread the other | ||
end, teeth down, through the correct slot in the front end plate; around one idler, the belt pulley on | end, teeth down, through the correct slot in the front end plate; around one idler, the belt pulley on | ||
the motor shaft, and the other idler; and through the corresponding slot in the back | the motor shaft, and the other idler; and through the corresponding slot in the back | ||
− | end plate. Place a belt tensioner on | + | end plate. |
+ | |||
+ | Place a belt tensioner on | ||
the belt (with the threaded hole pointing up for belt configurations A, B, E, F; or either up | the belt (with the threaded hole pointing up for belt configurations A, B, E, F; or either up | ||
or down for configurations C and D), and add another clamp. Pulling the belt taut and holding | or down for configurations C and D), and add another clamp. Pulling the belt taut and holding | ||
− | the clamp against the belt tensioner, tighten the clamp firmly. Insert a 14 mm long M5 screw | + | the clamp against the belt tensioner and the end plate, tighten the clamp firmly. |
− | in the belt tensioner: this screw adjusts belt tension. | + | Insert a 14 mm long M5 screw in the belt tensioner: this screw adjusts belt tension. |
Repeat for the second Y belt. | Repeat for the second Y belt. | ||
− | You may prefer easier access to the belt tightening screws | + | You may prefer easier access to the belt tightening screws. In that case, put the belt |
tensioners at the front of the machine. | tensioners at the front of the machine. | ||
− | The belts need to be fairly taut, but do not overtighten, or you'll | + | The belts need to be fairly taut, but do not overtighten them, or you'll |
damage the belt and reduce the life of the pulley and motor bearings. | damage the belt and reduce the life of the pulley and motor bearings. | ||
Revision as of 15:43, 28 January 2016
Preliminary instructions'
You'll need the other two belts (200 mm longer than your Y axis) and the remaining parts from Pack 11, with the belt tensioners tapped M5.
Refer to the X and Y carriage instructions for placement of the belt.
Make four clamps out of two oval plates, two 10 mm long M5 screws, and two nuts each.
Place one clamp a few millimeters from one end of the belt, and tighten firmly. Thread the other end, teeth down, through the correct slot in the front end plate; around one idler, the belt pulley on the motor shaft, and the other idler; and through the corresponding slot in the back end plate.
Place a belt tensioner on the belt (with the threaded hole pointing up for belt configurations A, B, E, F; or either up or down for configurations C and D), and add another clamp. Pulling the belt taut and holding the clamp against the belt tensioner and the end plate, tighten the clamp firmly. Insert a 14 mm long M5 screw in the belt tensioner: this screw adjusts belt tension.
Repeat for the second Y belt.
You may prefer easier access to the belt tightening screws. In that case, put the belt tensioners at the front of the machine.
The belts need to be fairly taut, but do not overtighten them, or you'll damage the belt and reduce the life of the pulley and motor bearings.
Congratulations for finishing the assembly of your eShapeoko!
Go To
- Previous step: X belt
- Back to assembly top page