EShapeoko 1.4 Assembly: Gantry - Revision history

Admin at 17:15, 22 September 2016

2016-09-22T17:15:16Z

Admin at 17:14, 22 September 2016

2016-09-22T17:14:59Z

Admin at 17:13, 22 September 2016

2016-09-22T17:13:40Z

Admin at 14:55, 22 September 2016

2016-09-22T14:55:43Z

Admin: Created page with "For this step, you need some parts from '''Pack 7'''. You also need the assembled X and Y carriages, and the the X rail. (TO DO: instructions for alternate configurations. In..."

2016-09-22T14:54:29Z

Created page with "For this step, you need some parts from '''Pack 7'''. You also need the assembled X and Y carriages, and the the X rail. (TO DO: instructions for alternate configurations. In..."

New page

For this step, you need some parts from '''Pack 7'''. You also need the assembled X and Y carriages, and the the X rail.

(TO DO: instructions for alternate configurations. In the meantime, use [[EShapeoko 1.3 Assembly: Gantry||the instructions for version 1.3]].)

[[File:EShapeoko 1.2 assembly gantry config D.png|frame|none|Gantry and X belt anchor for belt on the side (TO DO: update image to show the correct part LBA3.)]]

{| class="wikitable"
|-
!Item
!Part Number
!Part Description
!Count
|-
|1
|S5-14
|M5 14 mm cap screw
|8
|-
|2
|W5
|M5 washer (form A)
|8
|-
|3
|LBA3
|Belt anchor (belt behind rail)
|2
|}

Bolt the assembled Y carriages to the X MakerSlide using four screws each.
The screws holding the rear X rail also attach the belt anchors.
Orient the belt anchors as shown.

This is a good time to square the Z axis. Assemble this on a flat surface and
use a set square to ensure that the X carriage is vertical. Do this with the
X carriage near each Y motor plate, to make sure both ends are square. Tighten
the screws firmly.

== Go To ==

* Next step: [[EShapeoko 1.4 Assembly: Frame|Frame]]
* Previous step: [[EShapeoko 1.4 Assembly: X Carriage|X carriage]]
* Back to [[EShapeoko 1.4 Assembly Instructions|assembly top page]]

@@ Line 35: / Line 35: @@
 use a set square to ensure that the X carriage is vertical. Do this with the
 X carriage near each Y motor plate, to make sure both ends are square, and
-the X rail is at the same height at both ends. Tighten
+that the X rail is at the same height at both ends. Tighten
 the screws firmly.

@@ Line 1: / Line 1: @@
 For this step, you need some parts from '''Pack 7'''. You also need the assembled X and Y carriages, and the the X rail.
-(TO DO: instructions for alternate configurations. In the meantime, use [[EShapeoko 1.3 Assembly: Gantry||the instructions for version 1.3]].)
+(TO DO: instructions for alternate configurations. In the meantime, use [[EShapeoko 1.3 Assembly: Gantry|the instructions for version 1.3]].)
 [[File:EShapeoko 1.2 assembly gantry config D.png|frame|none|Gantry and X belt anchor (shown here with NEMA 23 motors) (TO DO: update image to show the correct part LBA3.)]]

@@ Line 3: / Line 3: @@
 (TO DO: instructions for alternate configurations. In the meantime, use [[EShapeoko 1.3 Assembly: Gantry||the instructions for version 1.3]].)
-[[File:EShapeoko 1.2 assembly gantry config D.png|frame|none|Gantry and X belt anchor for belt on the side (TO DO: update image to show the correct part LBA3.)]]
+[[File:EShapeoko 1.2 assembly gantry config D.png|frame|none|Gantry and X belt anchor (shown here with NEMA 23 motors) (TO DO: update image to show the correct part LBA3.)]]
 {| class="wikitable"