Template:Smooth Idler Wheel Assembly - Revision history

Admin at 00:09, 10 September 2016

2016-09-10T00:09:29Z

Admin at 00:08, 10 September 2016

2016-09-10T00:08:46Z

Admin at 20:24, 30 September 2013

2013-09-30T20:24:40Z

Admin at 20:21, 30 September 2013

2013-09-30T20:21:53Z

Admin: Created page with "File:EShapeOko_assembly_step_02_idler_wheel_1.png {| class="wikitable" |- !Item !Part Number !Part Description !Count |- !colspan="4"|''For each w..."

2013-09-30T20:19:05Z

Created page with "File:EShapeOko_assembly_step_02_idler_wheel_1.png {| class="wikitable" |- !Item !Part Number !Part Description !Count |- !colspan="4"|''For each w..."

New page

[[File:EShapeOko_assembly_step_02_idler_wheel_1.png]]

{| class="wikitable"
|-
!Item
!Part Number
!Part Description
!Count
|-
!colspan="4"|''For each wheel''
|-
|1
|EM-MW2
|Smooth idler wheel sleeve
|1
|-
|2
|EM-G5
|5 x 16 x 5mm bearing
|2
|-
|3
|EM-W5P
|5mm precision washer
|1
|}

Lay one bearing on a flat surface. Push an idler wheel sleeve over it
(lip up, of course). The parts are designed to force-fit, so push
firmly straight down. Thread this on a long M5 bolt, lip side first,
followed by a precision washer and the second bearing. Place the
second bearing on a flat surface, and push the idler wheel sleeve over
it too. Make sure the bearings are all the way in, with the first
bearing resting against the lip of the sleeve. Remove the bolt.

[[File:EShapeOko_assembly_step_02_idler_wheel_2.png]]

@@ Line 17: / Line 17: @@
      |2
      |G5
-     |5 &times; 16 &times; 5mm bearing
+     |5&nbsp;&times;&nbsp;16&nbsp;&times;&nbsp;5&nbsp;mm bearing
      |2
    |-
      |3
      |W5Pa
-     |5mm precision washer
+     |5&nbsp;mm precision washer
      |1
 |}

@@ Line 33: / Line 33: @@
 it too.  Make sure the bearings are all the way in, with the first
 bearing resting against the lip of the sleeve.  Remove the bolt.
 If the idler wheel does not rotate smoothly, see
 [[V-wheel and Idler Assembly Instructions#Troubleshooting|Troubleshooting]].

← Older revision		Revision as of 20:21, 30 September 2013
Line 35:		Line 35:

	[[File:EShapeOko_assembly_step_02_idler_wheel_2.png]]		[[File:EShapeOko_assembly_step_02_idler_wheel_2.png]]
		+
		+	If the idler wheel does not rotate smoothly, see
		+	[[V-wheel and Idler Assembly Instructions#Troubleshooting\|Troubleshooting]].

@@ Line 11: / Line 11: @@
    |-
      |1
-     |EM-MW2
+     |MW2
      |Smooth idler wheel sleeve
      |1
    |-
      |2
-     |EM-G5
+     |G5
-     |5 x 16 x 5mm bearing
+     |5 &times; 16 &times; 5mm bearing
      |2
    |-
      |3
-     |EM-W5P
+     |W5Pa
      |5mm precision washer
      |1
@@ Line 27: / Line 27: @@
 Lay one bearing on a flat surface. Push an idler wheel sleeve over it
-(lip up, of course).  The parts are designed to force-fit, so push
+(lip up, of course). The parts are designed to force-fit, so push
-firmly straight down.  Thread this on a long M5 bolt, lip side first,
+firmly straight down. Thread this on a long M5 bolt, lip side first,
-followed by a precision washer and the second bearing.  Place the
+followed by a precision washer and the second bearing. Place the
 second bearing on a flat surface, and push the idler wheel sleeve over
 it too.  Make sure the bearings are all the way in, with the first
-bearing resting against the lip of the sleeve.  Remove the bolt.
+bearing resting against the lip of the sleeve. Remove the bolt.
 If the idler wheel does not rotate smoothly, see